Tips From the Moving Company Pros: Ways To Move a Pinball Maker



With pinball making a substantial revival throughout the nation, Gentle Giant desires to make certain that these classic, stunning makers stay damage-free while being transferred. Oh, and we desire the people moving them to be safe, too.

At very first look, pinball machines can appear daunting to move due to the fact that of their size, fragility, and weight. Luckily, our knowledgeable Giants have a few tricks up their sleeves to guarantee your pinball is moved with ease.
Folding Down the Headbox

Most of modern pinballs (made in the last Twenty Years approximately) have a hinge system which allows the headbox to be folded down. Early pinball devices had their headboxes bolted on, utilizing either 2 or four bolts. All Electro-Mechanical pinballs use this system, in addition to the early Strong State machines.

Later on makers have hinges and use a latching system to keep the headbox upright. There may likewise be 2 bolts inside as added safety, in case the lock is broken or mistakenly un-latched.
Electro-Mechanical Pinballs

For Electro-Mechanical pinball machines, you have to get rid of the headbox rear gain access to panel to access to the bolts and plugs inside. Normally this panel has a lock on it to keep it in location, but in time the secret might have been lost. Frequently, there is a screw keeping this panel in location.

As soon as within, remove the bolts and unplug the big adapters that have wiring going down into the device. You might desire to label these connectors to put them back in the best area, but they ought to be different sizes, making it tough to plug back improperly.

You can now remove the headbox completely, or fold the headbox down onto the playfield glass. Ensure you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will help keep the back glass in place.
Early Solid State Pinballs

For early Strong State Pinballs, you will require to get rid of the back glass. There is a lock located on the headbox in one of 3 areas: the left-hand side at the top, right-hand side at the leading or on top of the headbox in the center.

As soon as opened, remove the back glass by lifting it up using the lift channel (at the bottom of the glass), and after that pull it out from the bottom.

Open up the back box light panel by raising the lock situated on either the left-hand side or right-hand side. The panel can now swing out towards you, and give you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs require you to raise the light panel in order to swing it open.

Now that you are within, you can get rid of the bolts, and any plugs that have wires going down into the machine. You may desire to identify these plugs to put them back in the ideal area. You may not need to remove the plugs, as the electrical wiring must be long enough to permit the headbox to be folded down.

At this moment, you can lock up the lamp panel and replace the back glass.
Modern Solid State Pinballs

For Data East, Sega, and Stern Modern pinballs, there is a turnable latch system situated at the back of the headbox. Utilizing the provided secret, turn the latch 90 ° counter-clockwise.

For Williams, Bally, and Gottlieb, you can easily unlatch the back box at the back of the machine. This is an easy setup and requires no tools.

You're done if you can now fold down the head box onto the cabinet. Make certain you utilize some foam, heavy cardboard, or blankets to protect the headbox from rubbing on the cabinet. Foam is best, as it will also help keep the back glass in place.

If you can not fold the head box down, then you need to enter. There is a lock situated at the top of the back glass in the. Use the supplied key to unlock, and eliminate the back glass by lifting it up from the bottom, and after that pulling it out from the bottom.

Next, you will have to get rid of the display screen panel. You can do this by raising it up and out. And lastly, open the lamp panel. There will be a latch located on either the right-hand or left-hand side. (Some newer Williams and Bally pinballs do not have a separate amp panel, it belongs to the back glass panel. And later on Sega and Stern pinballs utilize a fluorescent tube for the back glass lighting).

Remove the two bolts, put the back box back together, and fold down the head box onto the cabinet. Make sure you use some foam, heavy cardboard, or blankets to protect the headbox from rubbing on the cabinet. Foam is best, as it will also help keep the back glass in place.
Eliminating the Legs.

Pinball Device legs are this page held in location by 8 bolts. They will be either 5/8 inch or 9/16 inch heads. The contemporary pinballs have captive nuts or threaded plates inside for the bolts to screw into. These bolts can be eliminated, and the legs will come off.

However these threaded plates and captive nuts can be harmed, and the usage of additional nuts might have been needed. If this holds true, you will have to open the front door of the pinball, slide out the playfield glass, and raise up the playfield.

With the front door (coin door) open, move the lock down bar lock throughout and get rid of the lock down bar. Then move out the playfield glass, and put click to read more in a safe location. Next, raise the playfield by positioning your hand where the ball drains pipes, and raise the playfield up.

You must now have access to any nuts that might have been utilized. As soon as any nuts have actually been eliminated, change the playfield see it here glass and lock down bar, and lock the front door.

Make sure to mark or keep in mind which legs are for the front and back, as they will be changed in a different way to fit.
Packing the Pinball.

You are now prepared to transfer your pinball device. Before you pack it, make sure you remove the pinballs so they don't bounce around during transport.

It might be much easier to get rid of the legs simply prior to filling the device if you are moving the pinball utilizing a van or SUV. Get a buddy to help and have one of you supporting the pinball, while the other removes the front legs. Slide the machine in, then get rid of the back legs. It is a lot easier to fill the maker front initially.

Make sure you strap the pinball in, as you do not want it moving if you have to stop unexpectedly!

For Electro-Mechanical pinball makers, you require to eliminate the headbox rear access panel to acquire access to the bolts and plugs inside. (Some newer Williams and Bally pinballs do not have a separate amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs utilize a fluorescent tube for the back glass lighting).

If you are moving the pinball utilizing a van or SUV, it may be simpler to remove the legs just prior to loading the maker. Get a pal to assist and have one of you supporting the pinball, while the other removes the front legs.

Leave a Reply

Your email address will not be published. Required fields are marked *